- #Colt agent 38 special weight serial#
- #Colt agent 38 special weight full#
- #Colt agent 38 special weight series#
įrom its introduction, the Detective Special used Colt's ‘Positive Safety Lock’ ( hammer block), first featured on the Police Positive the mechanism interposes a bar between hammer and frame until the trigger is pulled, preventing accidental discharge if the hammer is struck (e.g., if a dropped gun falls onto its hammer) with the trigger forward. The new production run continued only until 1995, when Colt introduced its stainless-steel SF-VI as a replacement for the Detective Special. Only a two-inch barrel was offered, in blue or hard chrome finish. The post-1992 Detective Special is sometimes called the Fourth Series, and featured "composite" (rubber), wrap-around grips with a gold medallion. After reorganization, the company restarted production of the Detective Special in 1993. Ĭolt filed for bankruptcy protection in 1992. In 1986, facing stagnant sales numbers as well as rising production and labor costs, Colt discontinued production of the Detective Special. As with the previous two Series, a few nickel-plated guns were produced, and a 3-inch-barrel variant was again offered.
#Colt agent 38 special weight series#
The Third Series featured improvements to the revolver's internal lockwork as well. New, oversize wood gripstocks were introduced that covered the front frame strap.
#Colt agent 38 special weight full#
A new shroud extended down from the barrel, enclosing and protecting the ejector-rod, and the front sight was changed to a full ramp. Despite this alteration, the Detective Special's overall grip size remained unchanged, as Colt fitted the Second Series with new, lengthened gripstocks that extended below the frame. alt='colt agent 38 special weight' title='colt agent 38 special weight' />.
#Colt agent 38 special weight serial#
Because of this, assigning a given revolver to a particular issue is best done by serial number.ĭuring the 1960s, the grip frame of the Second Series Detective Special was shortened, matching that of Colt's other snub-nosed pistols, the Cobra and Agent. Transition from the First to Second Series was gradual, with some post-WWII Second Series guns retaining short ejector rods and checkered hammers. An optional hammer shroud was available from the factory to prevent the hammer from catching on clothing. The grip panels were plastic in 1947, but were changed back to wood starting in 1955 (first with a silver-tone Colt medallion, and later a gold-tone).
![colt agent 38 special weight colt agent 38 special weight](https://www.personaldefenseworld.com/wp-content/uploads/sites/6/2017/04/Colt-Detective-Special-1.jpg)
The right side frame screw has no locking pin, and the rear half of the front sight is a serrated ramp. The cylinder latch was smooth, and the trigger spur serrated. The ejector-rod was longer and had a groove in its knurled tip a three-inch-barrel variant was offered, with a yet longer ejector-rod. A rounded butt on the metal frame became standard in 1933, but pieces with the original square butt (like that of the Police Positive Special) continued to be produced into the 1940s. Other distinctive features included a shorter ejector-rod with an ungrooved, knurled tip a checkered hammer spur and cylinder latch, a "half-moon"–shaped front sight, and an overlapping screw and locking pin set-up on the right side of the frame. Compared to later production models, the First Series used a narrower frame, with reduced clearance between the frontstrap of the gripframe and the rear of the trigger guard. The First Series was produced from 1927 until 1946. Ĭolt's Detective Special went through several issues or series. The DS uses a slightly smaller frame than the Colt Official Police or Smith & Wesson "K" Frame revolvers, but is larger than the compact "J" frame used in Smith & Wesson five-shot revolvers. The Detective Special is by design a shortened and somewhat streamlined Colt Police Positive Special, sharing that revolver's slim "D" size frame and six round capacity. Lackluster sales of revolvers and a shift in the company's post-bankruptcy business model focussing on Department of Defense orders saw the elimination of the Detective Special from the product line in 1995. 38 Special, considered to be a powerful caliber for a concealable pocket revolver of the day. It was designed from the outset to be chambered for higher-powered cartridges such as the. Introduced in 1927, the Detective Special was one of the first short-barreled revolvers produced with a modern swing-out frame. As the name "Detective Special" suggests, this model revolver was used as a concealed weapon by plainclothes police detectives. The Colt Detective Special is a carbon steel framed double-action short-barreled revolver, and is an example of a class of firearms known to gun enthusiasts as "snubnosed", "snubbies", or "belly guns".